Estoflex GPS
High Performance Spray-able, Flexible Bitumen –Rubber Membrane
Estoflex GPS is a one component rubberized bitumen liquid membrane. It is a spray-able and fast setting, cold-applied, solvent based, bituminous mastic. It dries to tough, yet flexible coating, which will not be easily damaged by rain due to rapid drying time.
Estoflex GPS has been tested by SIRIM BHD, in accordance to BS 1881 Part 122:1983, on Water Absorption Test and complied with the specification in this data sheet.
Estoflex GPS is designed for used as a vapour barrier, waterproof and protective coating. It is used in civil engineering and building construction, such as:-
Colour | Black |
Adhesion | Adhere well to most surfaces |
Chemical Resistance | Resistance to dilute acids, alkalis and most salt solution. |
Solid Content, % | 65 |
Elongation at break, % ASTM D412 | > 600 |
Tensile Strength, N/mm2 ASTM D412 | > 2.0
(with Estop Geotextile) |
Water Absorption, BS 1881 Part 122 | < 0.5% |
Heat Flow Resistance | The cured film will not flow or sag under direct sunlight. |
Setting or Drying Time, hours | 2 – 3
(Depends on environment temperature and humidity) |
Substrate shall be free of dust, grease etc. before application.
All grooves, voids and honeycombs should be patched before the application of Estoflex GPS.
Estoflex GPS shall be applied with spray, brush, rubber squeegee or flat trowel.
The system is comprises of 2 neat coats at the rate of 1litre/m2/coat. The coating shall be dried before subsequent works.
Base screed with minimum gradient of 1:120, to receive Estoflex GPS, shall be laid if the floor is uneven and without required gradient, to achieve better waterproofing performance.
Estoflex GPS shall be applied with spray, brush, rubber squeegee or flat trowel.
Estoflex GPS shall be applied in 2 layers system.
First neat coat of Estoflex GPS shall be applied at the rate of 1 litre/m2.
Whilst the neat coat is still wet, lay the Estop Fibreglass / Estop Geotextile reinforce fabric and allowed to dry.
Second neat coat of Estoflex GPS shall be applied after the first neat coat is dry, at the same rate and allowed to dry.
For better performance, a layer of approved Fibre-reinforced shall be laid whilst the first neat coat is still wet and allowed to dry.
Estoflex GPS waterproofing system shall be protected from physical damage and UV, with a layer of cement sand screed.
The cement sand screed is recommended to laid 35 – 50mm thick and in panel form. The panel joints shall be filled with Estoliastic sealant.
For non-trafficable roof, Estoflex GPS can be protected with a layer of heat reflective coating.
Estoflex GPS | 205 litre drum
18 litre pail |
Estop Fibreglass | 240 m2 roll |
Estop Geotextile TS10 | 1000 m2 roll |
Estoflex GPS | 1 litre/m2/mm |
Estop offers a comprehensive range of high performance, high quality of product for both new and existing concrete surfaces. In addition, the company offers a technical support package to specifiers, end-users and contractors, as well as on-site technical assistance.
Estoflex GPS should be stored on pallets in dry conditions. Under these conditions, the product will have a shelf life of 12 months.
Estoflex GPS should not be swallowed or in contact with skin and eyes. Wear suitable protective gloves and goggles.
In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. If swallowed seek medical attention immediately – do not induce vomiting.
Estop manufactures and offers a wide range of complementary products, which includes waterstops, waterproofing products, grouts, anchors, specialized flooring products. In addition, a wide range of products formulated for repair and refurbishment of spalled concrete are available.