Crystallization Admixture Waterproofing
Download Data SheetEstomax MX200
Crystallization Cementitious Waterproofing
Estomax MX200 is a one part cementitious crystallization waterproofing coating. It consists of specially selected cements, graded hard wearing aggregates and additives supplied in powder form.
In the presence of moisture, the active chemical in Estomax MX200 penetrate concrete and react chemically with free lime to produce insoluble crystals. This crystalline growth reduces porosity by blocking capillaries and filling hairline non-structural cracks (up to 0.3 mm wide) caused by shrinkage or expansion. Unlike coating and membrane types of waterproofing, which only form a surface barrier. Estomax MX200, in the presence of water, continues producing crystals and a lasting imperviousness to water.
Waterproofing system for:
Color | Grey powder |
Water Permeability Test at 28 days, mm
DIN 1048-1991 Part 5 |
< 17.0 |
Testing water for suitability for use in human consumption
BS 6920 : Part 1 |
Complied |
Estomax MX200 can be dry sprinkled onto clean and pre- wetted lean concrete at the rate of 1.50 kg/m2 immediately prior to the casting of the structural slabs. Application by dry sprinkling distribution shall be over the surface by hand. The thoroughly wetted down lean concrete surfaces shall be free of lying water before application of Estomax MX200.
Use Estomax MX200 as it is, directly from container. Wearing rubber gloves, distribute the powder evenly by hand, over freshly poured concrete at the rate of 1.50 kg/m2 before final floating operation. It is best to distribute the powder at ½ the recommended rate in one direction, and the other half at right angle to the first application. Keep hand as close as possible to the surface to prevent material from blowing away. For large areas, a rotary type spreader may be used. Float slab and trowel to final finish.
Mix 25kg of Estomax MX200 with 8.25 Litres of clean water. Mix thoroughly for at least 2 – 3 minutes with a slow speed drill equipped with a paddle. For best result, add the clean water to Estomax MX200, and not the reverse. For larger batches, mix with a mortar mixer. Do not mix more material than can be used in 20 minutes (24 °C, 50% R.H.). If mixture thickens, re-stir to reduce consistency. Do not add extra water.
Use Estokote Brush (synthetic bristle) or plaster sprayer for the application of Estomax MX200 slurry coat at a rate of
0.75 kg/m2. Be sure to work slurry well into openings, rough surfaces, joints and routed out areas. When first coat has taken an initial set (usually within one hour), apply second coat at the same rate of 0.75 kg/m2 in perpendicular direction. If first coat has dried out, moisten surface before applying second coat.
Keep moist for a minimum of 24 hours after the application of Estomax MX200. After initial set, moist curing by continuous water spray. Treated surfaces shall be fog sprayed three to four times daily for 48-hour. For warmer climates, more frequent spraying may be required. It is important to keep the Estomax MX200 moist to allow the crystal formation to occur. Use Estop Estocure curing compounds for the curing purpose. Protect surfaces from foot traffic for 48 hours or heavy traffic for 7 days. Protect Estomax MX200 from extreme weather conditions such as rain, strong winds, high temperatures and freezing for a period of not less than 48 hours after application.
Estomax MX200 | 25kg bag |
Estokote Long Brush
Estokote Short Brush |
11 inch
9 inch |
Dry shake | 1.5 kg/m2
15.0 – 16.0 m2 / 25 kg bag |
Slurry coat | 0.75 kg/m2
32.0 – 33.0 m2 / coat /25 kg bag |
Estop offers a technical support package to specifiers, end- users and contractors, as well as on site technical assistance.
Estomax MX200 should be stored in protected, dry areas. When left in original unopened package, Estomax MX200 has a shelf life of 1 year.
Estomax MX200 is alkaline and contains chemicals that may cause irritation to the eyes and skin. Wear goggles, rubber gloves and long sleeves when working with this product. Seek medical advice in the event of prolong irritation
Estop manufactures and offers a wide range of complementary products, which includes waterstops, waterproofing products, grouts, anchors, specialized flooring products. In addition, a wide range of products formulated for repair and refurbishment of spalled concrete are available.