Externally Placed PVC Waterstop
Download Data SheetEstopper Rearguard waterstops are extruded from a high quality Polyvinylchloride compound, which has been formulated to provide excellent flexibility and longevity characteristic.
They are available as straight lengths and factory produced intersections.
Estopper Rearguard externally placed Polyvinylchloride waterstops are suitable for use in contact with potable water.
They are used typically in the following type of structures:-
The appropriate waterstop width depends upon the concrete thickness. The width of waterstop should not be greater than the thickness of the concrete.
Plain Web sections are used in contraction and construction joints
Above measurements are in mm unit.
Centre bulb sections are used in expansion, contraction and construction joints
Above measurements are in mm unit.
Externally placed Estopper Rearguard C waterstops incorporate a central fin to assist setting out shutter location. Externally placed Estopper Rearguard E waterstops incorporate a flat top centre box which allows movement to be accommodated in expansion joints. The box also provides a sealing to support joint fillers. Estopper Rearguard C & Eranges of waterstops are compatible to other Estopper CJ and EJ range of waterstops.
Compound | |
---|---|
Standard Conform | BS 2782 at 25°C |
Tensile Strength | > 10.0 N ⁄ mm² |
Elongation at Break | > 250% |
Hardness | Shore ‘A’ > 70 |
Profiles | |
Form | Extruded thermoplastic sections |
Colour | Black |
Hydrostatic Head | Up to 100m for 250mm profile Up to 60m for 200mm profile |
Heat welding equipment is available from Estop Sdn Bhd. Ensure the heat welding equipments are earthed by the green wire.
Waterstops must be installed so that they are securely held in their position while the concrete is being placed. Concrete must be fully compacted around the waterstops to ensure that no voids or porous area remain.
When install on ground slab where the waterstop is supported on blinding, Rearguard profile usually require no fixing. It shall be laid centrally over the joint (construction/expansion) line.
To vertical shutter, it is installed by nailing through the outer most flanges onto the shutter and leaving the nail head held into the concrete. This may prevent the waterstop being displaced when the shuttering is struck.
Jointing of Estopper Rearguard range waterstop is carried out using Estop Heat Welding Equipment. The ends to be joined are cut square and held in alignment. The ends are then pressed to both side of a special heated blade, until an even, molten bead of PVC appears around the section. The heated blade is then removed and the molten ends pressed fully together. The PVC cools to form a strong fusion welded joint.
An experienced technician would performed the jointing of the waterstops to satisfaction, subject to prior training and approval by ESTOP Technical Department.
Estopper Rearguard C 200 | 200mm x 15m roll |
---|---|
Estopper Rearguard C 250 | 250mm x 12m roll |
Estopper Rearguard E 200 | 200mm x 12m roll |
Estopper Rearguard E 250 | 250mm x 12m roll |
Estop offers a technical support package to specifiers, end-users and contractors, as well as on site technical assistance.
Estopper waterstops should be store under covered condition. The product has a shelf life of thirty six months.
Hot weld jointing of PVC waterstops results in the liberation of hydrogen chloride mist and vapour. The OEL (operational exposure limit) of 5 ppm can be exceeded in still air confined space, therefore ventilation must be provided.
Estop manufactures and offers a wide range of complementary products which includes waterstops, waterproofing products, grouts, anchors, specialized flooring products. In addition, a wide range of products formulated for repair and refurbishment of spalled concrete are available.